Rosette

I finished the rosette, almost.  There is still a little tweaking that I need to do at the joints of the wafers, but it is essentially what it will be.  The tile at the top is there primarily as reinforcement and fill.

The first step, of course, is layout.  To do this, I used my template, which has already be scribed, and traced the outline on the sound board.  I am going for a parlor-type guitar, which I interpret to mean a steel string guitar with classical like dimensions.  It also suits me because I play finger-style, and find myself switching between classical and steel strings, so some continuity in the dimensions works for me.  Consequently, I am using a 25 and 11/32nd inch scale length.  There are all sorts of ways of coming at this, but I have found that one purchase has repaid itself several times.  Get a fret rule from LMI.   Again, I am going for classical like dimensions, so I placed the 12th fret line at the top of the sound board, and marked the location of the 22nd fret on the center-line (the glue seam).  With my compass set at 1 7/8th inch diameter, I scribed the circle for the sound hole.

Once I had the tiles set out in the working scrap, which you can see beneath the rosette, the whole process became rather simple.  I set the router so it would ride within the channel that I had cut to fit the tiles, set the depth to just a whisker (about 1/64th of an inch) shy of the total depth of the tiles, double checked (actually, quadruple checked) to make sure that I would not be cutting through the soundboard at that depth, and then made the cut, testing first where it would be covered by the fretboard.  Once the initial cut had been made, I eased it out and in using the precision adjustment on my router jig to accommodate the tiles and the perfling strips.  When I was finished, I gave the rosette channel a coat of shellac to prevent bleed out from the glue.

I put all the tiles and perfling in place, leaving slight gaps at the seams so I could lift them out, one by one.  Beginning at the bottom of the rosette, I would lift out one tile, run a bead of superglue along each of the perfling strips.  I then replace and quickly position the tile between the perfling strips.  I kept going I had worked up both sides of the rosette.  I wiped away any squeeze out, and pressed the tiles into place with my fingers until the glue set.    

Before I cut out the sound hole, I did a couple of things.  First, using my template, I transferred the outline of the guitar to the back of the sound board.  That was a simple matter of using the 1/4 hole for the router pivot, and a similar hole at the center of the sound hole in my template.  When sanding the back, make sure that you never sand away the lines that they cannot be retraced.  I also leveled the rosette.  Nothing fancy there, I just used my trusty card scraper, newly sharpened, taking light passes until the rosette was level with the sound board.   I then sanded it using 120 grit sandpaper on my sanding block.  A word of advice, never sand without a sanding block.  It's amazing how quickly one can cut shallow hollows sanding without a block.  Mine is just a scrap of cherry with a cork face.  I wrap the sandpaper over it and hold it in place as I sand.

To cut out the sound hole, I swapped the 1/4 inch bit in my router to a 1/8th inch bit, made the adjustments so there would be a lip of redwood approximately 1/8th inch wide, made an initial cut, then cut through.   Some have jigs to round over the edge of the sound hole.  I don't.  I just use a light touch with some hand held sandpaper.  I can't tell the difference.
 

Cutting the Rosette Tiles

Here's how I do it.   I have a "precision" router set up.   You can see it in the photo, and I will admit right up from there are a few design flaws in it.  First, as you can see, the router base itself is attached to a plexiglass base.  This actually works rather well for the operation I am about to describe, in part because the base itself is wide enough that it covers the round of tiles.  There are three slots cut in the plexiglass, two for the adjustment mechanism, one for the pivot pin.

The adjustment mechanism is basically two steel rods that pass through the hold down and the pivot.  The two rods are epoxied into the pivot.  The two carriage bolts pass through the plexiglass and serve three purposes: (1) sliding in the slots, they serve as a gross adjustment, (2) they lock the steel rods in place, and (3) they lock the adjustment mechanism in place.  It isn't perhaps as visible in the photo, but but there is a saw kerf cut through the holes for the rods.  The carriage bolts pinch the rods when the wing nuts are tightened.  That is the first design flaw.  I should be able to loosen the rods without loosening the adjustment mechanism, but I have discovered that the "precision" mechanism can be adjusted by loosening the two carriage bolts just slightly, holding it in place with my thumb as I make the adjustments to the screw, which serves as the precision mechanism.   

The "precision" mechanism is simply a 1/4 by 20 steel rod that passes through a bolt inset into the adjustment mechanism into the pivot, where I inset a washer and a bolt.  To make the radius smaller, the "precision" mechanism is adjusted clockwise, pushing it out or closer to the router.  To make the radius larger, the "precision" mechanism is adjusted counter-clockwise, pulling it in or further from the router itself.  It works reasonably well, but there is some play in it, and that constitutes the second design flaw.  Someday, I may break down and buy the set up sold by Stew Mac.

The first step in making the rosette tiles is the template jig, the second is cutting the slices that will be used for the inlay, and the third is shaping the pieces to fit the jig.   My sound hole is 1 and 7/8 inches in radius, so I scribe a circle of that radius on a scrap of 3/4 MDF.  I also scribe a line at 2 and 1/8th for the inside diameter (ID) of the rosette, and then 2 and 5/8th for the outside diameter.   I scribe two copies of the rosette.

The next step is to use the rosette template to cut a couple of circles that will produce a template that is the mirror image of the rosette channel.   You can see it in the photo above.  I set my router to cut an OD channel, then an ID channel, leaving the mirror image of the rosette channel proud in the center.  This will be used to shape the inlay pieces.

The inlay material itself is a pile of wafers cut from the end grain of the padauk at about 1/8 thickness.   Normally, I would use my band saw for this, but I'm still awaiting parts, so I use a cross cut sled and a stop, and grit my teeth at the waste.  I put double stick tape on the proud rosette channel, then tape the wafers to that.  Make certain that they are secure.  If they wobble around you will not get precise cuts.  You can see that pictured above.   

I then cut the ID and OD with the router set up.  It pivots on the pin pictured.  It will take several passes, so again make sure the wafers are well secured with the double stick tape, and that the router base does not catch on an edge.   Cut the OD and then the ID with the router.  For the second batch, I leave the router setting in place for the ID, and cut the ID then make the adjustments to cut the OD.  For the third batch, I leave the router setting in place for the OD then make the adjustments to cut the ID, alternating until there are enough shaped tiles. 

The next step is to cut a channel that will fit the rosette tiles.   I consider this practice before I cut the channel in the soundboard, but it also serves a purpose as a jig to get the angles correct on the ends of the pieces.  I will cut a kerf through the rosette channel on the table saw, then use the kerf as a guide for trimming the ends with my gents saw, using the kerf as a miter box.  By the by, to get the pieces perfectly sized, I cut the rosette channel to fit the narrowest piece as precisely as possible, then make adjustments to the other pieces with sandpaper.  Be cautious not to round over the ends if you have already cut the miters, or sand to fit before you cut the miters.  Also, it always a good idea to have several more tiles than you need.  Because they are cut from end grain, they are fragile, and if you break one (and I broke two) you don't need to go through the whole business of the router set up again.

Thinking About Rosettes

There is the pragmatic side of the rosette -- actually doing the inlay into the soundboard of the guitar -- but there is the aesthetic side of it as well.  Beyond the actual choice of tone wood for the top, the rosette is the luthier's signature.   Consequently, I have been thinking about rosettes a bit lately, and if you'll pardon a bit of philosophy, I always come down on the side of simplicity.  As a devotee of Fretboard Journal, those guitars with elaborate inlays for the rosette and headboard, do not much appeal to me.  I can admire the skill (and it is much beyond me) but let's face it -- some are just gaudy.

Simplicity, for me, means nothing but wood (ok, and the BW perfling strips from LMI).  So, the rosette I have planned will be a simple affair, just a BW perfling line, followed by 1/2 of padauk inlay, followed by a WB perfling line.  There are two reasons for the padauk.  One, I have some scraps and off cuts that I've rescued from the flood.  It's the sort of thing that one can't bear to throw out, even if it has been soaked in pooh water, as my son puts it.  Two, I think the color complements and off sets the redwood that I'm using for the soundboards.  The perfling, with the white against the padauk, the black against the redwood, creates a border, and highlights it.  It's an irresistible combination.

Beyond that, there is an embellishment I have been contemplating.  Once the hardwood for the rosette is in place, it might be interesting to cut a channel in that, filling it with turquoise or another finely ground stone, drizzle it with CNA, then grind it smooth.  I don't think I'd want to put it directly in the redwood, in part because I think the grinding might damage it.  We'll see.

Radius Cutter

I found a little time to mess around in my shop this morning, and I came up with this radius cutter that I will use to cut my rosettes.  I was able to get into the school shop, and we have a great band saw with a re-sawing blade.  It cut the redwood like butter.  I will begin work on the soundboard, beginning with the rosette.  I have something in mind, but don't know how well it will work.  I'll give it a whirl and let you know if it does. 

The construction of the radius cutter is fairly simple.  I had some 1/4 inch oak scrap left over from the bench, so I cut a 1/4 in dado in the sides of the cuter, and at the same time, cut for the end pieces and the slide, but did them on both sides.  The pieces are laid out on my bench.
 

The slide works fairly well.  I took a section of what I'd cut for the end pieces, enlarged the dado slightly.  I drilled a 5/16th hole for the blade, and squared it off with my 1/4 inch chisel.  I drilled a 1/4 inch hole for the carriage bolt, then cut it in half with my gent's saw, pushing the blade up against one side of the dado.  The slide is held in place by the carriage bolt, which pinches the two pieces against the interior slats, and the blade is held in place with a small shaped piece of the slat.  It all pivots on a 1/4 metal pin that goes in the hole on the right. 

The blade is made from an old jig saw blade.  I did some very preliminary work on the grinder, but it will need some additional shaping.  I have in mind a chisel point so I can turn it in both directions, and will work on some when I get up in the a.m.  I should be able to do that without waking my wife and our guests.  Even with the point only partially sharpened, however, it did cut a good groove in a scrap of birch ply, at about 1/32 of an inch wide.